Complete Your Build
Screw-Together Case Kit for WisMesh Board ONE Meshtastic, MeshCore, WadaMesh Devices
A Durable Enclosure for Your WisMesh Board ONE
Go from a bare board to a durable, field-ready device with this compact, screw-secured enclosure, custom-built to house your WisMesh Board ONE and a 2000mAh battery.
What Makes It Stand Out
- Pocket-sized form factor that's compact and easy to carry for mobile applications
- Dedicated external-antenna SMA port for connecting high-performance LoRa antennas
- GPS-ready in both kits, built around a 2000mAh battery
This Is a DIY Kit for Makers
This product requires soldering and experience with electronics. By purchasing, you confirm you have the technical ability to assemble the components. A functioning WisMesh Board ONE is required.
Step One: Choose Your Kit
Select the kit that matches your needs. All kits include the case, switch, wiring pigtail, and assembly screws.
| Variant | GPS Ready | Antenna Included | Max Battery | Notes |
|---|---|---|---|---|
| Case | Yes | No | 2000mAh | For builders supplying their own antenna |
| Case + Antenna | Yes | Yes | 2000mAh | Ready to assemble with antenna included |
Step Two: Select Compatible Hardware
You will need these parts to complete your project. This case is designed around them for a perfect fit.
Required Components
- A functioning WisMesh Board ONE
- Battery: 2000mAh MakerNova LiPo Battery
- LoRa Pigtail: IPEX1 to SMA Adapter Cable
- An external LoRa antenna (if not purchasing the Case + Antenna kit)
▸ Case Dimensions
- 28mm x 52mm x 82mm (1.10in x 2.05in x 3.23in)
▸ Included in Every Case Kit
Every Kit
- Durable ASA Enclosure (Screw-Together, Front and Back)
- Power switch
- Wiring pigtail
- Assembly screws
This is a DIY kit for the case and hardware only. The WisMesh Board ONE, battery, LoRa pigtail, and antenna (unless the Case + Antenna kit is selected) must be purchased separately.
▸ Assembly Instructions & Wiring Guide (Read Before Building)
Important: Basic soldering skills are required. Review all steps before beginning.
1. Battery & Switch Wiring
SAFETY FIRST: Cutting battery wires requires extreme care. Do NOT let the red (+) and black (–) wires touch after cutting to avoid a dangerous short circuit.
- Prepare Wires: Cut the connector off your battery. Strip ~3-4mm from the battery's red and black wires, and from the included JST-PH pigtail wires.
- Wire the Switch (Positive +): Solder the battery's red wire to one of the outer pins on the switch. Solder the pigtail's red wire to the center pin on the switch.
- Connect Ground (Negative –): Solder the battery's black wire directly to the pigtail's black wire.
- Insulate: Securely cover the soldered ground connection with heat-shrink tubing or electrical tape.
Do not connect the pigtail to the board until final assembly.
2. Final Assembly
- Install the power switch and LoRa SMA pigtail into the case cutouts.
- Mount your WisMesh Board ONE into the case and secure it with screws.
- Use double-sided tape to secure the battery to the inside of the back cover.
- Attach your external LoRa antenna to the SMA connector. This is required before powering on.
- Plug the wired JST pigtail into the board's battery port.
- Close the enclosure and secure it with the final case screws. Test the power switch.
Meshtastic® is a registered trademark of Meshtastic LLC. MeshCore is an open-source mesh networking project released under the MIT License, and its name is currently the subject of an unresolved trademark dispute; it is used here only to describe firmware compatibility. Software components referenced in this listing are released under their respective open-source licenses, see GitHub for details. No warranty is provided for open-source software or firmware, use at your own risk. Hardware is covered by our 30-day return policy.
Material: All colors are 3D-printed ASA except Dark Green PLA+, which is PLA+ (tougher against impact, lower heat resistance).
